Oxy acetylene welding, sometimes referred to as "gas" welding, uses acetylene gas as the fuel for the welding torch. The flame produced by an. Oxy-fuel welding and oxy-fuel cutting are processes that use fuel gases and oxygen to weld and cut metals, respectively. French engineers Edmond Fouché and  ‎Apparatus · ‎Fuels · ‎Types of flame · ‎Safety. The principles of the oxyfuel gas welding process are presented including flame types, equipment, operating characteristics and techniques. (Oct. ).


Author: Wilber Goodwin III
Country: Zimbabwe
Language: English
Genre: Education
Published: 5 May 2014
Pages: 792
PDF File Size: 21.54 Mb
ePub File Size: 4.3 Mb
ISBN: 850-7-12976-407-7
Downloads: 25191
Price: Free
Uploader: Wilber Goodwin III


This flame contains white hot-carbon particles, which may be dissolved during welding.

Oxy-Acetylene Welding 101

This flame burns hotter. A slightly oxidizing flame is used in oxy acetylene welding, and a more strongly oxidizing flame is used in welding certain brasses and bronzes. Tack weld the joint every inch or so and clamps will help align the pieces for the tacks.

Expect to practice a lot before you develop proficiency with this process, oxy acetylene welding the more you practice, the faster your skill will develop.

A proficient gas welder can make a very good-looking, strong, and uniform weld bead. Heavier metals can be gas welded, too.

Aluminum can be gas welded, too, but this is an advanced process requiring special flux and a special welding lens. oxy acetylene welding

Oxy-fuel welding and cutting

Expect oxy acetylene welding practice a lot before you master gas welding aluminum! Put on a welding mask and gloves. Open the oxy acetylene welding pin valve slightly so that you can hear gas escaping, then light the gas with a gas striker. Adjust the acetylene flow until the flame is barely touching the nozzle, then open the oxygen pin valve slowly until the flame turns blue.

Oxy-fuel welding and cutting - Wikipedia

Move the tip of the flame over the edges of oxy acetylene welding metal pieces until the metal begins to glow red. Continue moving the flame, allowing more of it to touch the pieces of metal until small pools of molten metal begin to appear. Quite a few North American suppliers oxy acetylene welding begun selling propylene under proprietary trademarks such as FG2 and Fuel-Max.

Butane and propane do not react with each other and are regularly mixed.

Butane boils at 0. Vaporization is rapid at temperatures above the boiling points. The calorific heat values of both are almost equal.

Both are thus mixed oxy acetylene welding attain the vapor pressure that is required by oxy acetylene welding end user and depending on the ambient conditions. If the ambient temperature is very low, propane is preferred to achieve higher vapor pressure at the given temperature.

Oxy-Fuel Welding (OFW) Information | Why Use Oxyacetylene Welding? |

It is what chemically combines with the fuel to produce the heat for welding. This is called 'oxidation', but the more specific and more commonly used term in this context is 'combustion'.

  • Handbook-Oxy-Acet Cutting & Welding
  • How to Weld Oxy Acetylene | Sciencing
  • Oxy-acetylene welding process
  • Oxyacetylene Welding
  • How to Weld Oxy Acetylene
  • Why Use Oxyacetylene Welding?

In the case of hydrogen, the product of combustion is simply water. For the other hydrocarbon fuels, water and carbon dioxide are produced.

Oxy-acetylene welding

The heat is released because the molecules of the products of combustion have a lower energy state than the molecules of the fuel and oxygen.

In oxy-fuel cutting, oxidation of the metal being cut typically iron produces nearly all of the heat required to "burn" through the workpiece. It is also shipped as a liquid in Dewar type vessels like a large Thermos jar to places that use large amounts of oxygen.

It is also possible to separate oxygen from air by passing the air, oxy acetylene welding pressure, oxy acetylene welding a zeolite sieve that selectively adsorbs the nitrogen and lets the oxygen and argon pass.


This method works well for brazing, but higher-purity oxygen is necessary to produce a clean, slag-free kerf when cutting.

Types of flame[ edit ] Main article: Oxidizing and reducing flames The welder can oxy acetylene welding the oxy-acetylene flame to be carbonizing aka reducingneutral, or oxidizing.

Related Post